Fanuc Om Parameter List10/1/2020
CNC Electronics Returns Warranty Shipping Transaction About us Services Fanuc Swap Program Fanuc Parts Fanuc Restoration Fanuc Tests Utilized Fanuc Surplus Sell Your CNC Parts Website Information NEWS CNC CNC Western world: Fanuc Components Fanuc Components UK EU Privacy Page TOS Listing Sitemap CNC Electronics Inc.Please check the two 7-little bit digit screen in your GE Fanuc Alpha dog spindle module for sensors and mistakes.Alarms Description 01 The inside heat of the electric motor is higher than the described temperatures 02 The real motor rate is generally deviated from the commanded rate 03 The fuse of the DC link has broken (The voltage át the DC link is inadequate) This security alarm is examined when emergency stop is certainly cancelled.The temperatures sensor is definitely irregular, or the temperatures sensor wire is broken.
Fanuc Om Parameter List Plus Sell YourThe electric motor revolves at a velocity exceeding 115 (regular setting) of the optimum allowable quickness. This security alarm is released for SPM-15i and later.With SPM-2.2i to SPM-11i nevertheless, Alarm 12 will be released for the exact same cause. An exceedingly large current flowed into the DC link of the main circuit. Fanuc Om Parameter List Series Was NotIn result switching handle or spindle turning control, the switching operation series was not executed properly. This is certainly released if one second or more elapses from the transition of a switch request sign (SPSL ór RSL) until á strength lead state check sign (MCFN, MFNHG, RCH ór RCHHG) can make a changeover. A sum check is irregular. If this alarm is issued, change the SPM or SPM handle printed-circuit panel. ![]() A check will be made when the power is changed on. The described polarity of the placement sensor is incorrect. Serial conversation data moved between thé CNC and spindIe amplifier module includes an error. The sign of the position code is disconnected. An excessive insert (standard setting: load meter reading of 9 V) has been applied continuously for a certain period (regular setting: 30 seconds). The engine were unable to move as chosen, and provides ended or is usually rotating at a quite low rate. The error reverse overflowed. After crisis stop transmission insight, the electric motor is accelerated without being decelerated. This alarm isissued furthermore when the engine is not deactivated (the electric motor is not decelerated completely) when the accelerationdeceleration time (initial parameter environment: 10 seconds) offers elapsed after crisis stop indication input. The position where the one-rotation transmission of the place coder will be generated will be incorrect. The one-rotation signal of the place coder can be not generated. The one-rotation sign of the placement coder cannot end up being detected normally during twine cutting. The count value of placement coder transmission pulses can be abnormal. Stages A and N for the place coder have got a feedback pulse count of 4096 prev per spindle rotation. The SPM bank checks the heartbeat matters of stages A and B equal to the position coder each period a one-rotation sign is produced. The security alarm is released when a heartbeat count number beyond the given range is definitely detected. A value acquired by internal calculation in spindle synchronization surpassed the permitted range. The synchronization transmission (ITP) in communication data moved to and fróm the CNC halted. A large current going in the motor for a long time was detected. In spindle turning handle or result switching handle, a mismatchbetween the changing request signal (SPSL ór RSL) and thé energy lead state check indication (MCFN, MFNHG, RCH, ór RCHHG) proceeds during motor activation. The chilling lover for the handle circuit section has stopped. An mistake occurred during communication (connection JX4) between spindIe and amplifier. This alarm can become issued just when Dual Check out Safety is definitely in make use of. The security alarm happens if, in protection signal setting Chemical, the spindle engine rotation rate surpasses the safety speed. The spindle amplifier connection status does not go with the hardware environment. A safety parameter error occurred. The outcome of the spindle amplifier swiftness check does not fit the outcome of the CNC check. The sign of the electric motor sensor will be disconnected. The Processor test were unable to finish normally 75 This alarm can be issued only when Dual Check Safety is usually in use. An error occurred in the CRC check. The spindle safety function has not happen to be executed. The outcome of the spindIe amplifier axis number check will not match up the result of the CNC axis amount check. The result of the spindle amplifier basic safety parameter check out does not really go with the outcome of the CNC basic safety parameter check. An unusual operation was recognized in the initial test. The placement where the one-rotation sign of the motor sensor is usually generated is definitely incorrect. The one-rotation transmission of the engine sensor will be not generated. The SPM bank checks the heartbeat matters of phases A and T each period a one-rotation indication is generated. The spindle sensor sign was disconnected. The one-rotation sign of the spindle sensor occurred in an wrong location. No spindle sénsor one-rotation indication occurred. A spindle sensor indication is irregular. The high temperature sink air conditioning fan is not working. Fanuc Om Parameter List Serial Communication DataC0, D1, G2 An mistake occurred in serial communication data between thé CNC and spindIe amplifier component. M3 In spindle changing a mismatch is usually found between the switching request indication (SPSL) and the internal status of the motorspindle sensor indication switching signal (submodule SW). Sensors 4, 11, 30 are usually combination alarms and need to referenced with the various other alarming component of the CNC control or leader drive system other than the spindle component.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |